直纺亮光抗倒伏波浪扁平涤纶FDY的开发

探讨了直纺83 dtex/114 f波浪扁平涤纶全拉伸丝(FDY)的工艺制备过程。试验证明,在熔体输送温度276~282℃,纺丝温度286~290℃,喷丝板规格DIO φ104 mm-114孔、"王"字形,环吹风压10~15 Pa,含油率1.1%~1.2%,卷绕速度3 800~4 200 m/min的工艺参数下纺制83 dtex/114 f波浪扁平涤纶FDY时,生产稳定,满卷率高,外观情况良好,袜带均匀亮丽,可批量生产。此新产品可用于制作高档布艺沙发表层面料,具有抗倒伏、色彩艳丽等功效。     

Electrical Breakdown Properties and Space Charge Formation in High Temperature Region in Ultraviolet Ray Irradiated PVC

Polyvinyl chloride (PVC) is the most popular insulating material for electric wiring instruments. However, an exothermic reaction above 150 °C may cause deterioration of the insulating properties of PVC. Therefore, it is important to clarify the heat degradation in PVC, not only to investigate the ignition of electrical wiring products but also to use electrical products safely. It is known that ultraviolet (UV) irradiation causes chemical deterioration of PVC and an increase in its conductivity. Generally, it has been thought that the electrical breakdown properties, electrical conduction, and insulating performance are affected by space charge accumulation in an insulating material. A high temperature pulsed electroacoustic (PEA) system usable up to 250 °C has been developed, and the PEA system can measure the space charge distribution and conduction current in the high temperature range simultaneously. In this investigation, the space charge distribution and conduction current were measured up to electrical breakdown in a non‐UV irradiated sample (normal PVC) and in 353 nm and 253 nm UV‐irradiated PVC samples in the range from room temperature to 200 °C in a DC electric field. In the short wavelength UV irradiated PVC sample (253 nm, 300 h), a deterioration of breakdown strength at 90 °C to 150 °C and negative packet‐like charges were observed at 60 °C and 100 °C, a positive charge accumulated in front of both the anode and cathode above 90 °C, and a higher electric field near the cathode side because the positive charge of the cathode side was greater.     

基于3D打印技术复制砂浆节理的剪切试验及峰值抗剪强度模型

为进一步研究节理三维形貌特征与节理峰值抗剪强度的关系,首先采用巴西劈裂试验获取了自然劈裂岩石表面,通过三维扫描技术获取了节理面形态的高精度点云,通过逆向建模得到了自然岩石表面的立体模型,结合3D打印技术制作出了与自然岩石表面一致的PLA模具,以3D打印获得的底模通过水泥砂浆浇筑了含有自然结构面形貌的相似节理面试样。PLA模具与复制材料差异较大,复制材料在凝结过程中不易与PLA模具黏结,进而使脱模过程较为方便,不会破坏节理面。同时PLA模具可重复进行相似材料复制工作,具有可重复使用的优点。然后进行了具有5组形貌面的20个水泥砂浆节理面在4种不同法向荷载情况下的结构面剪切试验,得到了结构面剪切位移-荷载曲线。研究了结构面峰值抗剪强度、峰值位移、剪切刚度影响因素。节理经过剪切后形貌面出现不同程度的磨损,其磨损范围与等效高差分布范围基本一致,并且在等效高差为剪断破坏模式且成片的区域磨损较为严重。在新粗糙度指标基础上提出了新的峰值抗剪强度模型,经试验对比显示出新模型的有效性。在新模型基础上提出了一个简化模型。对比发现新模型简化后其计算精度较新模型有所降低但由于所需参数减小计算较为方便,新模型简化结果精度虽然有所下降但是还是比Barton公式精度高。     

GIS气体高压开关在阳煤五矿变电站的应用

针对阳煤五矿广场变电站的高压开关老化问题,为了保证安全性,采用了GIS气体的高压绝缘开关进行了改造。在改造后,变电站的安全性得到了显著提高,设备运行可以节省成本200多万元。     

化学气相沉积钨涂层的研究现状与进展

化学气相沉积钨涂层具有工艺简单、技术成熟度高、涂层综合质量优异等特点，广泛应用于国防、航天、核工业等领域。首先介绍了化学气相沉积钨涂层的原理和特点，重点讨论了化学气相沉积钨涂层的工艺及应用研究现状，包括化学气相沉积钨涂层微观组织控制工艺及在耐辐射、耐磨耐蚀和高温防护领域的应用，同时对新型化学气相沉积钨涂层技术的发展进行了展望。一是改善现有工艺存在的反应气源与反应产物毒性大等问题，满足绿色环保的发展要求；二是改善现有工艺存在的沉积温度高、沉积速率偏低等问题，实现在不同衬底表面的高效、高质量沉积；三是改善现有化学气相沉积钨涂层结构与功能单一等问题，满足构件对钨涂层高性能和多功能的需求。     

Effect of Moving Speed of Charged Metallic Spherical Electrode on Electrostatic Discharge

In this investigation, the nature of the electrostatic discharge (ESD) that occurs when a charged object moves toward a stationary grounded object is experimentally clarified. The spark lengths, discharge currents, and induced voltages in a magnetic probe were measured when a charged metallic spherical electrode connected to a 422 pF capacitor approached a stationary grounded object, which was the current target, for different moving speeds of the charged metallic spherical electrode in a range of 1 mm/s to 100 mm/s. The charge voltages of the capacitor were +6.5 kV and +10 kV. Based on the results, the average gap length shortened with the speed of the spherical electrode. The average peak values of the discharge current and the induced voltage were likely to increase with the speed of the spherical electrode. The average rise times of the discharge current and the induced voltage were likely to drop with the speed of the spherical electrode. The relation between the spark length and the discharge current due to the ESD can be explained qualitatively by using an equation derived from the spark resistance formula proposed by Rompe and Weizel.     

Voltage reference architectures for low-supply-voltage low-power applications

This paper presents a voltage reference generator architecture and two different realizations of it that have been fabricated within a standard 0.18 μm CMOS technology. The architecture takes the advantage of utilizing a sampled-data amplifier (SDA) to optimize the power consumption. The circuits achieve output voltages on the order of 190 mV with temperature coefficients of 43 ppm/°C and 52.5 ppm/°C over the temperature range of 0 to 120°C without any trimming with a 0.8 V single supply. The power consumptions of the circuits are less then 500 nW while occupying an area of 0.2 mm² and 0.08 mm², respectively.     

不同制样方法对直流辉光放电质谱法测定氮化硼中27种杂质元素的影响

讨论了3种制样方法对直流辉光放电质谱法(dc-GDMS)检测氮化硼中的Na、Mg、Al、Si等27种杂质元素的影响。3种制样方法分别如下所示:方法1,直接把氮化硼压在铟薄片上;方法2,把氮化硼压在铟薄片上后,再盖上一层铟罩;方法3,把压碎后的氮化硼放在针状钽勺上。在优化的辉光放电参数下对比了3种不同制样方法对基体信号强度的影响。试验表明:在方法1中,当氮化硼尺寸约为3mm×3mm,厚度小于1mm时,基体¹¹B的信号可达1.8×10⁷ cps;在方法2中,选择铟孔大小合适的铟罩,基体¹¹B的信号可达1.0×10⁷ cps;方法3获得基体信号强度比方法1、方法2高一个数量级。大部分元素在中分辨率下可获得较好的结果,而对于在高分辨率下也较难分离的元素,可选择丰度较低的同位素在中分辨率下进行测定,如Ge选择⁷⁰Ge⁺,Se选择⁸²Se⁺,Cd选择¹¹¹Cd⁺,Sn选择¹¹⁹Sn⁺,Ag选择¹⁰⁹Ag⁺,Pt选择¹⁹⁴Pt⁺。氮化硼中的杂质元素含量可通过样品片中待测元素含量减去来自于铟薄片或钽勺中该元素贡献的含量来计算获得。将样品平行测定5次,相对标准偏差均在20%以内。对于Al、Si、Ti等元素的测定,3种制样方法的测定结果基本一致;方法1、方法2中检测到的In含量较大,使得铟中的Ni、Cu对氮化硼的测定值影响较大;方法3由于钽中Fe、Cu的贡献导致氮化硼中Fe、Cu的检测值较大,但方法3获得的基体信号强度大,可降低部分元素的检出限,如Cr、Mn、Ga、Ge等。综上所述,方法3为优选方法。     

碎软煤层条带瓦斯地面高效抽采技术研究

为了提高碎软煤层条带瓦斯抽采效率和效果,基于目前地面瓦斯抽采主要采用垂直井或从式井的方式抽采效果差、效率低的现状,通过理论和实验分析论证了穿岩层压裂改造煤储层的可行性,提出了在目标煤层顶板岩层中钻水平井,并通过垂直向下射孔以及采用泵送桥塞分段进行压裂的方式进行地面瓦斯抽采。试验结果表明:顶板分段压裂水平井单井产量高、高稳产期更长、产量衰减更慢;有效水平井段控制区域内瓦斯下降均匀,更有利于进行条带瓦斯抽采;相同投资条件下,采用水平井的方式瓦斯抽采效率和投入产出比更高。     

硅渣和玻璃粉直接烧结制备多孔材料的气孔结构与力学性能

以硅渣和玻璃粉为原料,采用粉体直接烧结法制备多孔材料,研究了烧结温度(700~900℃)、烧结时间(15~120min)和升温速率(10~100℃·min^-1)对多孔材料表观密度、气孔率、物相组成、抗压强度的影响。结果表明:气孔结构均匀性随烧结温度的升高而降低;表观密度随烧结温度的升高先减小后增大,随保温时间的延长而增大,随升温速率的增大而减小,气孔率的变化趋势与表观密度的相反;多孔材料的主要物相为玻璃相和硅、SiC、SiO2、Ca2Al2SiO7等结晶相,且结晶度随烧结温度的升高而降低;抗压强度随烧结温度的升高呈先增大后减小的趋势;当烧结温度为750℃,升温速率为30℃·min^-1,烧结时间为30 min时,多孔材料的主晶相为硅和Ca2Al2SiO7,抗压强度最大(1.60MPa),表观密度为0.43g·cm^-3,气孔率为80%。